Electric Hot Cutter
Application
（1） Sponge foam: sponge, foam, foam slotting, EPS, EVA, pearl cotton, bubble pad and so on
（2） Rubber plastic: plastic, rubber, plastic opening, acrylic cutting, benzene board cutting, KT board, advertising cloth, carpet,PVC pipe, all kinds of plastic sheet, nylon pipe, plastic pipe, cable and so on
（3） Cable: synthetic fabric, cable, braided belt, ton bag,PVC rope, Nylon rope, packing belt, mesh fabric, etc
（4） Cloth leather category: cloth, non-woven cloth, curtain cloth, canvas, nylon cloth, waterproof cloth, leather, carpet and so on
（5） Other categories: cork, dirt cleaning, aluminum film
Precautions
Parameter
Please confirm that the machine is turned off and unplugged
before disassembling the welding machine so as not to be
injured by live wires or components inside the machine.
The welding machine generates high temperature and high
heat, which may cause fire or explosion when used incorrectly,
especially when it is close to combustible materials or explosive gas.
Please do not touch the air duct and nozzle(during welding work or
when the welding machine has not completely cooled down),
and do not face the nozzle to avoid burns.
The power supply voltage must match the rated voltage
marked on the welding machine and be reliably grounded. Connect
the welding machine to a socket with a protective ground conductor.
In order to ensure the safety of the operators and the reliable
operation of the equipment, the power supply at the construction site
must be equipped with a regulated power supply and a leakage protector.
The welding machine must be operated under the correct control of the
operator, otherwise it may cause combustion or explosion due to
high temperature.
It is strictly forbidden to use the welding machine in water or muddy
ground, avoid soaking, rain or damp.
| Model | LH8100 | LH8150 |
| Rated Voltage | 230 V / 120 V | 230 V / 120 V |
| Frequency | 50 / 60 Hz | 50 / 60 Hz |
| Power | 100W | 150W |
| Temperature Regulation |
Adjustable | Adjustable |
| Blade Temperature | 50-600°C | 50-600°C |
| Power Wire Length | 3 m | 3 m |
| Product Size | 24 X 4.5 X 3.5 cm | 24 X 4.5 X 3.5 cm |
| Package Size | 28 X 23 X 8 cm | 28 X 23 X 8 cm |
| Net Weight | 395 g | 395 g |
| Model | LH8200 |
| Rated Voltage | 230 V / 120 V |
| Frequency | 50 / 60 Hz |
| Power | 100W |
| Temperature Regulation |
Adjustable |
| Blade Temperature | 50-600°C |
| Power Wire Length | 3 m |
| Product Size | 24 X 4.5 X 3.5 cm |
| Package Size | 28 X 23 X 8 cm |
| Net Weight | 395 g |
| Model | LH8250 |
| Rated Voltage | 250 V |
| Frequency | 50 / 60 Hz |
| Power | 100W |
| Temperature Regulation | Adjustable |
| Blade Temperature | 50-600°C |
| Power Wire Length | 3 m |
| Product Size | 24 X 4.5 X 3.5 cm |
| Package Size | 28 X 23 X 8 cm |
| Net Weight | 395 g |
Main Parts
1.Blade 2.Blade Holder 3.Auxiliary Mount
4.Temperature Button 5.Indicator Light 6.Switch on/off
7.Power Wire
Operation
1. Turn on the power.
2. Adjust the temperature button, the higher the temperature if rotated inward and the lower the temperature with outward rotation.
3. Press the temperature button and put the blade on the object. Turn it on and warm up for seconds. It recommended to test cutting waste materials before cutting. 4. In the process of use, when the blade reaches the cutting temperature, intermit- tent point switch to maintain the consistency of temperature and speed, improve the work efficiency, prolong the service life.
5. Attention: it is recommended to keep the temperature stable by intermittently releasing the heating switch after 10-15 minutes of continuous heating to prevent overheating and damage to the Electric Hot Cutter.
Installation of Blade
1. When the tool is cool and not energized, unscrew the two nuts clamping the knife leg with hexagonal wrench in counter-clockwise direction.
2. Insert two legs of the blade into the holes of the two cutting heads and then tighten the two nuts to ensure knife legs and cutting heads in full contact. Improper assembling would not heat up the blade.
Clearance of Blade
After using period of time, the material residue might be stuck on the blade, please use wire brush to clean.
Packing list
Body
Small spanner
Wire brush
Tool kit
“R”Shape Blade（LH8100）
15cm Straight Blade（LH8150）
20cm Straight Blade（LH8200）
25cm Straight Blade（LH8250）
Warranty
· This product guarantees a 12-month shelf life from the day it is sold to consumers. We will be responsible for failures caused by material or manufacturing defects. We will repair or replace defective parts at our sole discretion to meet the warranty requirements.
· The quality assurance does not include damage to wearing parts (blade), damage or defects caused by improper handling or maintenance, and damage caused by falling products. Irregular use and unauthorized modification should not be covered by the warranty.
· This product is not designed for continuous heating for a long time. Improper use will lead to deformation of the plastic at the front end of the Electric Hot Cutter due to overheating, which is not within the warranty scope.
Maintenance
· It is strongly recommended to send the product to Lesite company or authorized repair center for professional inspection and repair.
· Only original Lesite spare parts are allowed.
